10/30/2022 0 Comments Aaf recovery tool av700![]() ![]()
AAF RECOVERY TOOL AV700 PCBei gestecktem Kabelīootet der Receiver nur, wenn der PC an ist. Nach Einrichten und Installieren das Nullmodem KabelĪm Receiver abziehen. + libeplayer2.so.0.0.0 behebt Probleme beim stoppen von mkvs + Lautstärkenanpassung für AC3 hinzugefügt + kleinere start Optimierungen/fixes (Atevio) + sporadische Hänger am Ende von Aufnahmen gefixt USB hard drive be disconnected from the receiver AAF RECOVERY TOOL AV700 UPDATEIf the software already installed version 2.00, they shall recommendĭuring the update process must be connected to the external AAF RECOVERY TOOL AV700 UPGRADEAppear This is not a fault but an internal test mode,Īfter the upgrade of the receiver is in "Menu -> Service Menu ' Note: Only works if no HDMI cable is plugged in parallel to Scart Cableĭuring playback of a recording may display the message: "Error pos same" Need to "SPDIF" and switched the receiver to be restarted Pipes to Scart output when "decoded PCM" -> to bring this SI-update overnight started even if just a recording ![]() Icons integrated VFD, except Dolby DigitalĪfter PIP / HDMI resolution adjust unit does not operate, except for EXIT / MENU button ![]() Timeshift - TS stops too early, recording is achieved as the end-stops TS, althoughĬould shift - shift to terminate (before and EXIT REC), one receiver Timeshift - problem in reaching the 4GB barrier With firmware version 2.02 the following improvements and new features are achieved: In the service menu you can see if the new software has been installed.įirmware version 2.02 for UFS 910si (BN 20,210,105) and UFS 910sw (BN 20210089) This must be new in a workshop or via PC and network cableīe installed. Turn off the receiver during the update process in any case from, or you theĪll software lose. (See perform "service menu", "update via USB" or "operation ofĪfter completion of updating the settings are initialized and is running again. This update, you can also use the USB ports of the receiver You fi nd the software under the "Service" "Software and Download" "receiver" The updates can also get on the Internet. Of updating the components you selected earlier.Ĭheck for a software update, the time setting! If you have made all the settings for updating your receiver, go to theĬheckbox "Start Update" and press the button. The submarine ² (BIOS of the box) is not affected. For damage to equipment that is caused by any inaccuracies in this recovery image, the author can not be held liable. The use of this Image Recovery at your own risk. * Step 9: Remove the USB stick only appears when another image on the TV.Ĭurrent status: ufs912_recovery_v2.0B2_1.1.zip AAF RECOVERY TOOL AV700 TV* Step 8: The box on and hold the TV / RADIO key on the box to "EMERGENCY BOOT" in the display.ĭuring the procedure, the box automatically reboot several times. * Step 7: Using the USB stick is now stuck in the front USB port of the switched-off box. * Step 5: Remove the USB stick as soon as' UPDATE SUCCESS! " the display of the box is. * Step 4: The box on and keep the TV / RADIO key on the box to "EMERGENCY BOOT" in the display. * Step 3: Insert the USB stick is now in the front USB port of the box turned off. System can continue to take place directly to step 7. * Step 2: If no change between E2/Neutrino back to the org. ![]() (Folder structure retained)Īs you see can be found on the USB stick is now following folder structure: * Step 1: For this, the recovery image on a USB stick copy. Importing the Recovery Image is normally via USB. There is no intervention required by RS-232. Image Recovery This enables a complete square of the new flash Kathrein UFS-912 in case of error or for the return of E2/Neutrino to original system. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |